Home > Epson Stylus > Epson Stylus Pro 7800 Sensor Error

Epson Stylus Pro 7800 Sensor Error

Contents

BUT, if I unplug it for a spell and start it up again, I get the usual humming.I also tried holding the < ^ > buttons while starting but that did Faint printout or gaps Try one or more of these solutions: Make sure that the ink cartridges do not exceed the expiry date. NO MAINTENANCE TANK INSTALL THE RIGHT SIDE MAINTENANCE TANK The right side maintenance tank is not set in the printer. However, the cost of the 7800 is considerably less than the former. More about the author

I cleaned the wiper blade and ran the head cleaning, and nozzle check again. For Mac OS X, see Advanced Settings. Sign up! Support hours and days are subject to change without notice. navigate to these guys

Epson Stylus Pro 7800 Ink Cartridge Error

Rubo Thanks for the incite. by makdaddy on Oct 24, 2011 at 5:31pm Add comment Please sign in to comment 0 makdaddy, probably getting "suckback" following cleaning cycles. Make sure it is correct for the paper you are using. See PLATEN GAP.

Any ideas? I wish to convert it to Epson 9800 for the 8 colour printer. I've gotten a new static IP for it, but need to release the old one. Epson Stylus Pro 7800 Specs If the cable and connection are good, the main board has most likely failed.

The problem is I have been looking for weeks on the internet for instructions without any luck. Epson Stylus Pro 7800 Review If the roll paper is not set properly, wind the excess paper up and set the paper lever to the secured position. Note the error number, then turn the printer off. http://www.manualslib.com/manual/255373/Epson-Stylus-Pro-7800.html?page=154 I am going in a few days to convert my 9400 into a 9800...Good luck to evryone.

Ink starvation due to poor seal in the ink path (cartridge, lines, damper), failing printhead, damaged\\dirty wiper blade, or failing main board. Epson Stylus Pro 7800 Firmware Update Unplug the unit. Make sure no foreign objects are inside the printer. After converting and using some other files .prn it showed as 7800.

Epson Stylus Pro 7800 Review

Canvas 280gsm polyster matt. Remove the pump\\cap assembly and look at the printhead from the back of the unit. Epson Stylus Pro 7800 Ink Cartridge Error One SS clean after reading some info on this site. Epson Stylus Pro 7800 Price Has anyone encountered this problem?

Right-click EPSON Stylus Pro XXXX, then select Properties. http://strongboxlinux.com/epson-stylus/epson-stylus-on-error.php Can anyone tell me where the relevant sensors are and how to get to them. See page 126 for instructions. • When you send a print job, make sure your print options are set • correctly. But, now I cannot get the MB to recognize the left bank of ink cartridges. Epson Stylus Pro 7800 Maintenance Tank

You may also want to check the tubes and connections to the pressure air pump for leakage. See Advanced Settings. If you buy the refill pads instead of the maintenance tank, it comes with a chip resetter. click site If so, attach the paper guides to the printer.

It must be replaced as a whole unit. Epson Stylus Pro 7800 Driver On internet is says it is 00010037 Print Head thermistor error. To start with:I had a 7400 with bulk ink system installed.

Set the paper lever to the released position, then check that the roll paper is set properly and that there is no external obstruction in the sensor detection area.

Make sure it is correct for the paper you are using. thanks by steveapple on Jun 26, 2012 at 3:30pm Add comment Please sign in to comment 0 Hi, I have a 7800 which of course is similar to the 9800. Make sure the paper is not folded or wrinkled. Epson Stylus Pro 7800 For Sale We have recently had a few 7800/9800 refill carts that seem to have the wrong chips attached from the manufacturer, so I suspect this is what is causing your error, and

See Printer Color Management. If I flip the lever and close it again the error goes away and it goes on to print untill the next one is ready to print and then it starts Let me know if you come up with anything as well. - dean1968 have you found a solution ?i am stucked with the same problem :after main board replacementI tried to navigate to this website If I turn it off and back on again, it may or may not hum.

Then turn it back on.