Home > Error Code > Electrolux Oven Error Code F1

Electrolux Oven Error Code F1

Contents

Inspect the overlay. Unfortunately the only solution to fix it is to replace the EOC. The consumer or reader is individually responsible for his or her use of the information supplied and uses this information at their own risk. The front left burner has quit working but only the center burner, not the outer two rings. navigate here

I'm lucky because it did not happen to me, but I have heard about such problems. The cause of this problem is a faulty EOC. The EOC board was recently replaced (F10 went away after new board was installed, but now it is back). Range/Stove Fault Codes My Range is flashing a "F" something.....what does this mean??

Electrolux Oven Error Code F23

I am confused if it's the EOC or if there could be a problem with the oven relay board. But if you bought it from AppliancePartsPros.com then you can easy return the part for warranty exchange. Thank you for your question. My first question to them is the email at the bottom of this email chain.

Mark Mason 11 560 visningar 14:47 Gas Range Oven Control Board (part #316455410) - How To Replace - Längd: 3:06. Gene. Specifically the orange wire on the connector adjacent to the only non square or rectangular black component on the board. Frigidaire Oven F1 Error My wife is suspicious of the temperature, however.

I pressed the cancel button, but the error comes back. Electrolux Oven Error Code F01 Also the model number you posted is incomplete. Note: "F3" is displayed when oven is in active mode or an attempt to enter an active mode is made. 3. http://www.shopyourway.com/questions/1109331 Gene // Mar 15, 2015 at 7:23 pm Hello Frank, I do not think this is common with Frigidaire ovens.

Get Your Ugly Christmas Sweater here. Frigidaire Electronic Oven Control The part number for the relay board is 316443918 You can order the part by clicking on the part number. You may want to check the igniter by measuring the current drawn by the igniter. In all occurrences the alarm is accompanied by a display of "F1".

Electrolux Oven Error Code F01

the main board with the buttons and clock etc.. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/512950-electrolux-frigidaire-stove-error-code-f1.html If fault returns, replace the oven's electronic control board. Electrolux Oven Error Code F23 Do you know the name of a good shrink in the Northeast? Electrolux Oven F11 Error Code Usually an hour or so after it has been shut off.

Please check back in a few minutes. check over here Sounds like the EOC has gone bad again. So we were back to blaming the EOC. If less than 500 ohms, replace the oven temperature sensor probe. Electrolux Oven F10 Error Code

It is a Frigidaire Model # FFEF3048LS Any help appreciated! Or the low voltage transformer is going out. Ed Gene // May 6, 2015 at 9:35 pm Hi Ed, Put everything back together and give it a try. http://strongboxlinux.com/error-code/electrolux-oven-error-code.php There are a few potential causes for the F1 code, depending on which boards and touchpads are used.

You may want to replace it as well. Frigidaire Gallery Oven F3 Error Code If the sensor and wiring are good, replace the EOC. What Your Appliance Error Code Really Means.

wall oven, following your directions I measured the sensor resistance which was 1077.

The part number for the EOC is 316443865 Good luck. Robert Wilson // Mar 11, 2015 at 5:18 pm Hi Gene, i have a frigidaire stove model cfef366emh , it has given me an error f11 , i did disconnect the By MarkF in forum Whirlpool/KitchenAid/Roper/Estate Replies: 3 Last Post: December 27th, 2005, 06:51 PM Posting Permissions You may not post new threads You may not post replies You may not post Frigidaire Self Cleaning Oven F1 Error Would the most likely problem be the temp.

Some info and tips on oven temp sensors Newer 4 digit fault codes - Maytag, JennAir, Magic Chef Newer Frigidaire fault codes Some newer GE built in oven fault codes are Ed // Apr 27, 2015 at 11:01 am Hi Gene, Per your suggestion, I cut the 2 violet wires (the 2 running between the EOC and the RTD temperature sensor) and Gene. weblink And the last letter to the model is F.

Reply With Quote July 15th, 2008,07:24 PM #7 Jake View Profile View Forum Posts Visit Homepage Appliance Tech - Admin Join Date Aug 2004 Location McMullen Valley, Arizona Posts 79,471 You Gene // Sep 14, 2015 at 6:59 pm Hello Jack, Sorry for the delay. The relay board is located behind the oven rear panel what means you do have to pull the oven of the cabinet. Please verify the model number and repost it.

The part number for the EOC is 316455410 Good luck. P.S. We pulled out the oven temperature sensor. You can get them in a hard ware store or order from AppliancePartsPros.com by clicking on the following part number.

Prior to testing make sure that the shaft is set to the off position, disconnect the wire harness and use an ohmmeter to measure the resistance between pins 1 & 2 I placed my order for the needed EOC today. If not, I understand that it is likely either the thermometer or the panel. Press BAKE for 6 seconds. “UPO 00” will appear in the display. 3.

I have an Electrolux model#EW30DF65GSB.