I think there is smth wrong with the CPU, can somebody who having the same problem check their CPU heatsink's temperature ?? this was a free console so will to do ANYthing to get it to load. Cluster C2. Joined: Dec 5, 2005 Messages: 2,227 Featured Posts: 0 Location: Richmond, VA Country: Quoted from lenselijer: call with microsoft to check if you still have warranty, be sure to put the my review here
Anybody got any more suggestions? I tried loosening the bolts to where they were just loose enough so the heatsync didn't wobble. It can also often be caused by a cold joint under the Southbridge(if it wasnt caused by an update). 1020 - NAND issue (loose pin/ bad flash) 1021 - This error don't be a scumbag - just ask. --==ERROR Codes==-- If there is a problem with the Xbox360 The LEDs in the ring of light will flash in a particular pattern.
No matter how much pressure is applied to the GPU it still gets the 0022 GPU error. this kind of temperature would leave you with a crispy chip or circuit board!)... It can also be related to wiring the diodes while JTAGGING. How and how long are you overheating your console?
i under stand the over heating on the v1s or mayb they dropd there 360 off some stairs and some hardware is failing to load lol xl All Pro lx, The theory: rather than use pins or a zif socket or one of the usual methods MS decided to essentially float a chip on a series of solder balls. Used aluminum foil on GPU as a last attempt. 0102 Area Code The LEDs will now blink the second number of the code.
Most attackers fall into one of four categories, each with their own favored tactics, techniques, and procedures. Error Code 0102 Powerdvd It could be possible after bad update. Also what ratio of the subsequent failures are due to this or the joins failing again I doubt anyone knows as the same error codes would appear but I can see Otherwise the other 99% of the time this error is just the GPU in need of reball.
ive done quite a few x-clamp fixes but have never ran across this problem after install. 0102 Country Code A more permenant fix will cost you more and takes a bit more skill because you have to replace the X-Clamps with bolts (again, there are videos on youtube). Read about them now! Join Now For immediate help use Live now!
Replace only the GPU (the low profile heatsink stuck under a hot DVD drive with nothing to pull air across the heatsink) [as the fan shroud leads up to the back http://www.se7ensins.com/forums/threads/xbox-360-error-codes-explained-and-how-to-fix-them.2480/ I've already redid heatsinks thermal paste on both GPU and CPU, and it seems to work fine for about 10 min, then it goes back to this error. Xbox 360 Error Code 0102 Can also be a component that is missing or damaged so look for missing parts near the GPU. How To Get Secondary Error Code Xbox 360 I do have holes drilled in my chassis so it was easy for me to have the xbox half together so i could quickly turn it off and adjust the screws
You can fix this issue by using thin cardboard (such as from a cereal box, posterboard, or stiff note cards) to seperate the air path to the two fans.... Many believe that their 3-light ring of death is simply overheating.... Just replace the thermal paste with Arctic Silver 5. it's a Xenon? Xbox 360 Error Codes
some kits only come with the parts for oneClick to expand... seve91 on 2011-07-06 13:02:15 : Had a board with 0102 error. Ask! http://strongboxlinux.com/error-code/error-0102-xbox-fix.php Connect with top rated Experts 14 Experts available now in Live!
I let it 2RLOD for about 3 minutes then shut it off for an hour or so. P0102 Diese Funktion ist zurzeit nicht verfügbar. but it keeps coming back, does anybody know what i'm doing wrong??
The best solution is to replace the thermal compound. Appears to be one of the RAM chips for me. No, create an account now. Gamestop I have a heatgun, artic silver 5, and penny's to replace thermal pads.
Heating the chip avoids this somewhat by ideally not being powered during the event. E75 - This error is related to the network chip, might be power related or so.This can happen while installing and NME 2. Creep: creep is one of the primary failure methods of metal at high temperature, long story short higher temperatures mess it up and higher stress messes it up. It can also happen because of a bad eeprom or a wrong security sector.It can also be a problem with the internal connection of the harddrive to the mainboard...According to XBH:
Mine worked for 6 months after. Add a new comment: Here you can enter your comment... He did some research on it, and he says it's a GPU error. It can also be caused by a faulty DVD power or SATA cables(edsondario & Fios89) E65 - This error occurs if something goes wrong while flashing the drive or installing a
they told me that there was no halo 3 coming out and that the 360 was unmoddable because it had no screws in it. Register now! haza12d, Nov 12, 2009 #8 kingofall Regular member Joined: Sep 1, 2009 Messages: 177 Likes Received: 0 Trophy Points: 26 ill try that one next. All add-ons are available either by Google search or on Curse.com.
Sportsmaniac1322, Mar 21, 2009 Top #9 Member lenselijer GBAtemp Maniac Joined: Mar 27, 2006 Messages: 1,495 Featured Posts: 0 Country: i've fixed alot of 360 with xclamp but the problem will THINGS TO TRY Let the Xbox 360 console cool. Can be caused by a backwards power cord or faulty power cord to dvd player. 0032 - Might be temp sensor related, check out 0030 0033 - Might be temp sensor It is actually a hard drive error not overheating.
According to XBH: Error within Xam E72 - This error is related to a loose pin or a not existent NAND chip, can also happen if you flashed it badly with E67 - This error occurs when your harddrive is defective, it might still work sometimes....Hard drive timed out during reset. I let it sit overnight, and tried it in the morning. 3RLOD 0022 again. The CPU heatsink is almost as wide as the GPU heatsink, except it is over 4 times taller and has a copper tube built in for additional cooling...
Yesterday, 02:59 AM Welcome To Our Services My Shop Dumps : dumps - atm . Help with RROD After Xclamp fix. Mostly it is one of the outer solder balls on the side facing the (H)ANA chip so a shim increases the chanced of success quite a bit. Reflowed CPU and the xbox is now stable.
Stay logged in Se7enSins Gaming Community Home Forums > Microsoft Consoles > Xbox 360 > Xbox 360 Support > Log in or Sign up Home Home Quick Links Submission Guidelines Notable There is a little scratch in the motherboard, but i don't think its cutting any track.