Note that this response code is documented here for historical purposes only. Melnikov IESG X.7.13 User Account Disabled 525 Sometimes a system administrator will have to disable a user's account (e.g., due to lack of payment, abuse, evidence of a break-in attempt, etc). At my work we use Oracle 11g DB server which supports an ERP application. The problem is specific to exchange 2007 and there is a MS tip that covers it. Source
Jakob Kruse10-Mar-2014, 01:47 AMPeter, I don't know anything about easymail, but you can use CDO, which is already available on just about every Windows machine out there. This is a special case of X.7.21. (This violates the advice of Section 6.1 of [RFC6376].) [RFC7372] (Standards Track); [RFC6376] (Standards Track) M. Use WinRoute.450"Requested action not taken – The user's mailbox is unavailable". For domain names, this means the address portion to the right of the "@" is invalid for mail. [RFC3463] (Standards Track) G.
Response: 550 5.7.1 Unable to relay for [email protected] - 8 We already tried to send data with the email "[email protected]" in our microsoft outlook and it works. Message content or media issues are under the control of both the sender and the receiver, both of which must support a common set of supported content-types. [RFC3463] (Standards track) G. Meaning, if both your address and the recipient's are not locally hosted by the server, a relay can be interrupted.It's a (not very clever) strategy to prevent spamming. Vaudreuil IESG X.3.1 Mail system full 452 Mail system storage has been exceeded.
The error is "unable to connect Error 9. I have tried using the IP and server name and still get the same error. Vaudreuil IESG X.4.YYY Network and Routing Status The networking or routing codes report status about the delivery system itself. Smtp Error Codes 554 This code may shed light: Move (oMailtx(Self)) to hmailtx and Move (EasyMailSMTPObjSSL(hmailtx)) to bSSLActive Thanks, Peter Vincent Oorsprong18-Feb-2014, 11:37 PMPeter, You first create a DataFlex object of the EasyMail.SSL class.
Vaudreuil IESG X.5.5 Wrong protocol version Not given A protocol version mis-match existed which could not be automatically resolved by the communicating parties. [RFC3463] (Standards Track) G. If the error persists, check all your recipients' addresses and if you've been blacklisted.541The recipient address rejected your message: normally, it's an error caused by an anti-spam filter.Your message has been Simple as adding your server to the list, or selecting All except the list below. On the Network tab specify the IP address of the voicemail pro server on the bottom section as the remote server and on the top make sure that port 25 is
The error is "unable to connect Error 9. Smtp Error Codes And Acknowledgements This is primarily intended for use with clear text authentication mechanisms. Check again your recipients' accounts and correct any possible misspelling.512A DNS error: the host server for the recipient's domain name cannot be found. Vaudreuil IESG X.1.9 Message relayed to non-compliant mailer Not given The mailbox address specified was valid, but the message has been relayed to a system that does not speak this protocol;
The selected mechanism SHOULD then work for authentications in subsequent sessions. [RFC4954] (Standards Track) R. http://www.emailaddressmanager.com/tips/codes.html On the Permission Groups tab make sure that ONLY Anonymous Users is enabled. Easymail Smtp Object Activex Control Multiple Buffer Overflows Security and policy status issues are assumed to be under the control of either or both the sender and recipient. Rm Easymail Smtp Settings Inactive Forum User Voicemail Pro and Exchange 2007 February 27, 2009 06:55 PM (in response to Inactive Forum User) No I did not.
You should contact your ISP and ask them to allow you as a certified sender. this contact form Vaudreuil IESG 4.XXX.YYY Persistent Transient Failure A persistent transient failure is one in which the message as sent is valid, but persistence of some temporary condition has caused abandonment or delay This has been working fine. I put a valid address there and it is now working like a charm. Smtp Server Error Codes
PS This is very old Flexcom code. Vaudreuil IESG X.5.YYY Mail Delivery Protocol Status The mail delivery protocol status codes report failures involving the message delivery protocol. Vaudreuil IESG X.7.6 Cryptographic algorithm not supported Not given A transport system otherwise authorized to validate or decrypt a message was unable to do so because the necessary algorithm was not have a peek here Currently, this is not used.2: The server has completed the task successfully.3: The server has understood the request, but requires further information to complete it.4: The server has encountered a temporary
Any suggestions?Thanks,Paul Red Flag This Post Please let us know here why this post is inappropriate. Smtp Error Codes Wikipedia This memo does not discuss the merits of any such filtering, but provides a mechanism to report such. All Rights Reserved All material, files, logos and trademarks within this site are properties of their respective organizations.
I was just going to suggest the same thing, also on the voicemail pro server ensure that you can telnet to port 25 of the exchange 2007 server, doing the above Siemborski, A. The client SHOULD retry with a new authentication mechanism. [RFC4954] (Standards Track) R. Smtp Error Codes Rfc Vaudreuil IESG X.1.3 Bad destination mailbox address syntax 501 The destination address was syntactically invalid.
peter ista [home] Voicemail Pro and Exchange 2007 March 3, 2009 04:55 AM (in response to Inactive Forum User) Look in the registry Go to HKEY_LOCAL_MACHINE -> Software -> Avaya -> Klensin IESG X.2.0 Other or undefined mailbox status Not given The mailbox exists, but something about the destination mailbox has caused the sending of this DSN. [RFC3463] (Standards Track) G. I tried this code "Set EasyMailSMTPObjSSL of hmailtx to True" and I got an error. Check This Out Vaudreuil IESG X.5.3 Too many recipients 451 More recipients were specified for the message than could have been delivered by the protocol.
Vaudreuil IESG X.4.5 Mail system congestion 451 The mail system was unable to deliver the message because the mail system was congested. Vaudreuil IESG X.6.6 Message content not available 554 The message content could not be fetched from a remote system. Try to send it again segmenting the list in different parts.449A routing error.Like error 432, it's related only to Microsoft Exchange. Email About Tech Follow us: We deliver.
Such error messages are using codes like 4.X.X, where X.X are used in order to give more precise information about the error; 5 means there is a permanent/fatal error related to Network issues are assumed to be under the control of the destination or intermediate system administrator. [RFC3463] (Standards track) G. There was an error connecting to the SMTP mail server." Has anyone else had to add in extra commands to handle GMail requirements like:- Gmail SMTP TLS/SSL required: yes Use SMTP