Home > Not Found > Elastix Error Wanpipe Configuration File Not Found

Elastix Error Wanpipe Configuration File Not Found

Contents

DAHDI_SPANCONFIG failed on span 1: No such device or address (6) Alguien podri indicarme a que se refiere? Enabling wanrouter init scripts ...(start:8, stop:91) Command failed: update-rc.d wanrouter defaults 8 91 Failed to install boot scripts ---------------------------------------------------------- WANPIPE v3.5.20 Installation Script Copyright (c) 1995-2010, Sangoma Technologies Inc. ---------------------------------------------------------- WANPIPE National ISDN 2 2. Unable to connect to remote asterisk (does /var/run/asterisk/asterisk.ctl exist?) Error executing command: asterisk -rx "zap show channels" Would you like to continue? 1. navigate here

I'm not sure how it ran *before* I did the update, though I didn't check the uname, dangit. Where are those compile scripts at now? NO [1-2, ENTER='YES']:1 Would you like to enable hardware fax detection? 1. Also to reconfigure a single DLCI. /usr/sbin/wanrouter start wanpipe2 wp2_fr18/usr/sbin/wanrouter stop wanpipe2 wp2_fr18/usr/sbin/wanrouter restart wanpipe2 wp2_fr18 To view current status and configuration of active devices: /usr/sbin/wanrouter status Error Debugging After a

Wanpipe1.conf Not Found

Save cfg: Restart Asterisk & Wanpipe when convenient 3. You can also click an option from the menu bar to go directly to a new section. it does not appear that the VICIbox build *includes* the sources for Asterisk, et al; I don't see them anywhere on the machine.

Like it's supposed to. Normalmente un "egrep wanrouter /var/log/messages | tail -n 100" te daría las últimas 100 lineas que tengan que ver este comando. To start/stop/restart WANPIPE devices listed in /etc/wanpipe/wanrouter.rc file: (default is wanpipe1) /usr/sbin/wanrouter start/usr/sbin/wanrouter stop/usr/sbin/wanrouter restart To start/stop/restart single wanpipe device: (eg: wanpipe2) This command is useful when running multiple devices and Fatal: Error Inserting Wanpipe Please steer me in the right direction.

Did upgrade OS and to trunk, did not configure any hardware -- to use VoIP as uplink. Wancfg_dahdi you'll need dahdi to load (but there is no sep dahdi_dummy, except in lsmod where it's visible). WAN Protocols Support Protocols: Frame Relay, CHDLC, PPP, ATM, X25, ADSL, TDM API Default for: Wan Routing, Data & Voice API devel. 2. find more info TE_HIGHIMPEDANCE YES NO Enable/Disable RX High Impedance mode.

So I reinstalled it a fifth time, and just didn't do the OS upgrades. No Sangoma Isdn T1/e1 Cards Detected Confirmation tail -f /var/log/messages 5. No such command 'stop now' (type 'core show help stop now' for other possible commands) Failed to stop asterisk using command: 'stop now' Forcing Asterisk Down Sin embargo desde la interfaz YES 2.

Wancfg_dahdi

Baylink Posts: 77Joined: Wed Aug 06, 2008 10:58 am Top Reply with quote by williamconley » Thu Apr 14, 2011 3:58 pm you're already there. http://bugs.elastix.org/view.php?id=1953 Even if it *looks like* it's convinced it. :-{ The number of reinstalls it took me to figure out what was actually going on would curl your hair. :-) Baylink Wanpipe1.conf Not Found HDB3 2. Wanpipe Latest Version Baylink Posts: 77Joined: Wed Aug 06, 2008 10:58 am Top Reply with quote by williamconley » Thu Apr 14, 2011 10:17 am try using the scratch installation instructions to re-install

El valor correcto seria TE_RX_SLEVEL=120 Saludos, dCAP Christian Cabrera R. check over here English (US) Español Ayudar Contáctenos Mod Ir al inicio Impulsado por vBulletin™ Versión 5.2.3 Derechos de Autor © 2016 vBulletin Solutions, Inc. E1 3. FE_LCODE B8ZS AMI HDB3 T1 T1/E1 E1 Front End Line Coding. Sangoma Wanpipe Install

The driver modules are for 2.6.34.0, and my kernel's the shipping 2.6.34.7. YES - Use all channels 2. Save cfg: Stop Asterisk & Wanpipe now 4. his comment is here MTU TDMV_SPAN Number Define span number for this device TDMV_HW_DTMF YES NO Enable/Disable Hardware DTMF detection (Echo Cancellation module is required)

FATAL: Module dahdi_dummy not found. Sangoma Pri Card Installation highlight= I tried installing dahdi manually and got this error: You do not appear to have the sources for the 2.6.34.7-0.7-pae kernel installed. Zaptel/Dahdi - PRI CPE 2.

Press any key to continue: ------------------------------------ Configuring analog cards [A200/A400/B600/B700/B800] ------------------------------------ ------------------------------------ Configuring USB devices [U100] ------------------------------------ ################################################## ################# # SUMMARY # ################################################## ################# 1 T1/E1 port(s) detected, 1 configured 0

EuroISDN 6. Graphical Mode: wanpipemon -g Raw trace: wanpipemon -i -c tr Interpreted trace: wanpipemon -i -c ti Alarms : wanpipemon -i -c Ta Question: If I'm just running a small office with 4 DIDs, a few handsets, 1 remote phone, voicemail, callerid... Would you like to install WANPIPE start-up scripts? (y/n) y ################################################## ###################### # Sangoma Wanpipe # # Dahdi/Zaptel/SMG/TDMAPI/BOOT Configuration Script # # v2.39 # # Sangoma Technologies Inc. # # Copyright(c)

LBO 0DB 7.5DB 15DB 22.5DB 0-110ft 110-220ft 220-330ft 330-440ft 440-550ft 550-660ft 120OH 75OH T1 T1 T1 T1 T1 T1 T1 T1 T1 T1 E1 E1 Define Line Buil-Out (transmit waveshape) DAHDI Tools Version - 2.5.1 Notice: Configuration file is /etc/dahdi/system.conf line 0: Unable to open master device '/dev/dahdi/ctl' 1 error(s) detected Error executing command: dahdi_cfg -v Would you like to continue? Recuperar clave de root en sistema CentOS Linux Configurar E1 en Elastix o Asterisk Reset Your Ubuntu Password Easily from the Live CD... weblink While the module will still *work*, this badly confuses the *updater*, which believes it must uninstall that module to avoid a mismatch, and nothing you tell it will convince it otherwise.

Sangoma SMG/sangoma_prid- PRI NET [1-12]:1 Select switchtype for AFT-A101 on port 1 1. edit: seems to have worked now but i suspect it's because of the change Kumba made. This script will compile and install WANPIPE modules into the currently running linux kernel. Compiling WANPIPE LibStelephony API library ...Failed. -- Note this library is not mandatory its safe to continue install Press [Enter] to continue...

Save cfg: Stop Asterisk & Wanpipe when convenient 5. hp?t=17706 Baylink Posts: 77Joined: Wed Aug 06, 2008 10:58 am Top Reply with quote by Trying » Fri Apr 15, 2011 4:31 am Then this must be the same issues If this option is enabled, PCISLOT/PCIBUS options are ignored (NOTE: A101/A102/A104/A108 T1/E1 is treated as the same card). Is that clean enough? :-) Baylink Posts: 77Joined: Wed Aug 06, 2008 10:58 am Top Reply with quote by williamconley » Thu Apr 14, 2011 4:18 pm seems clear to

Si No OK OK Cancelar X Now I'll run YoU by hand. Asterisk won't start and stay running, even after a manual restart of the vicidial service, with the message shown in the title (and all the messages commonly associated with that). User space programs2.1 Configuration (/usr/sbin)wancfg: Wanpipe configuration tool cfgft1: Wanpipe FT1 config tool for S508FT1 and S5143 cards (For all other cards use wancfg) 2.2 Operation (/usr/sbin) wanconfigWanpipe operation

Check the events and driver statistics. Zaptel/Dahdi - FX0 - Kewl Start 11.