hope this helps.QUOTE(SwisyNinja @ Feb 19 2010, 09:50 PM) im gettn 0002 wo any heatsinks but also w heatsinks. So, if the point shorts out due to ****** LED wiring or just some stupid mistake, it will draw excessive current, but the motherboard won't know it. Info about Mosfets. hope this helps.You most likely need to reflow. navigate to this website
i have played around with the bolts, trying different tightnesses. I was waiting for the correct washer to arrive so i just put a small piece of electrical tape between where the contact was made. A dental hook tool, or hemostats should work fine. Still no go.
replace MOSFETS Page 1 of 10 [ 94 posts ] Go to page 1, 2, 3, 4, 5 ... 10 Next Print view Previous topic | Next topic Xbox 360 Possible Tried it and it wouldn't even boot, just an immediate 3RROD, still showing 0002 though. I'm about done with this one. Bitte versuche es später erneut.
No picture on the screen. -Fans do not spin, and PSU may show red or orange light. -After it shows the 3 red lights, secondary error code will be 0001 or I then loosened all the screws until the xbox turned on with no error. does anyone have any suggestions?thanks. Erro 0002 Xbox 360 Your cache administrator is webmaster.
Tried reflowing JUST the CPU with a heat gun and poured some no clean flux underneath it. Error 0002 Xbox 360 Slim This doesn't necessarily mean the PSU brick is broken, but that one or more of the components that regulate the voltage across the board to the various parts may be damaged. Tried reflowing JUST the CPU with a heat gun and poured some no clean flux underneath it. this website gpu cpu fan disk drive...
I fixed that by putting electrical tape on the bottom of the cage where the motherboard touches. Błąd 0002 Xbox 360 Do not try using the paste with a solering iron, or else it can roll up and get under the chip and cause a short. This doesn't necessarily mean the PSU brick is broken, but that one or more of the components that regulate the voltage across the board to the various parts may be damaged. Grim might actually be useful if you had pictures.
You can find it online on eBay, some forum’s Trading Posts etc (XS, GI etc) If your Xbox 360 is faulty, here are some things you can try. 1) Sometimes, it http://suhastech.com/fix-0001-0002-errors-on-your-xbox-360/ Solutions:Clean your heatsinks and add a very very small amount of Arctic Cooling Paste between the GPU and the heatink and the GPU and the heatsink....THIS IS VERY IMPORTANT. Error 0002 Xbox 360 Solucion also, when i power on the xbox, the fans turn on for a second or two, then turn off. Xbox 360 Error 0002 Fix The xbox 360 uses special transistors called "metal–oxide–semiconductor field-effect transistors", or MOSFETs to regulate the volatege.
the mosfets i replace was 726 48 13NG from the original 801 48 13NHG. useful reference Here is some info on 0001 and 0002 error 0001 0002 Spoiler You can not test a mosfet chip while it is in circuit, so it must be desoldered first if If I tightened the CPU bolts at all it would 0002, but with them loose it ran like a champ. Be sure that all the screws are tighten at the same level and pressure. Xbox 360 Error Code 0002
I then ,with the 360 powered on, tightened each screw a full rotation until the 0002 error came on and the xbox shut off. RROD Working - Dauer: 3:25 SeaEyeProductions 248 Aufrufe 3:25 Reparar 3 luces rojas de Xbox 360 - Dauer: 27:25 ComoHacer.eu 281.843 Aufrufe 27:25 Weitere Vorschläge werden geladen… Mehr anzeigen Wird geladen... MikeLawry, Jan 2, 2011 MikeLawry, Jan 2, 2011 #4 Comrade Sit Nomine Digna Retired Messages: 12,430 Ratings: 6,180 Jan 2, 2011 #5 jmd almighty said: ↑ Tbh if you get one my review here I will have no clue how to replace MOSFETs..Do you know anybody on this site that does?Click to expand...
always making sure that the neoprene washers are the only washers touching the motherboard. Xbox 360 Jasper Failure Rate You basically just replace those little chips. Even though there are a couple different brands used for the MOSFETs, I have only seen this one controller chip on the bottom of older boards.Now once again it seems Microsoft
Soldered it in place and green lights returned. Got rid of the xclamps, and then baked in a conventional oven at 250F for 15 min. Is it likely that it is a MOSFET issue? Xbox 360 Jasper Power Supply Melde dich bei YouTube an, damit dein Feedback gezählt wird.
Back to top #14 hyfall381 hyfall381 X-S Expert Members 602 posts Location:Connecticut Xbox Version:v1.0 360 version:v1 (xenon) Posted 14 August 2010 - 09:53 PM having the same problem. i replace the 2 mosfets under the cpu and replace the controller chip still 0002. Help?Thanks! get redirected here Materials needed: * Soldering Iron * Mosfets (just get some free samples from onsemi.com) Procedure: 1) Open up the Xbox 360 and pull out the motherboard. 2) You will have to
No picture on the screen.-Fans do not spin, and PSU may show red or orange light.-After it shows the 3 red lights, secondary error code will be 0001 or 0002. -Nothing always making sure that the neoprene washers are the only washers touching the motherboard.