Home > Xbox 360 > Error 0002 Xbox 360 Slim

Error 0002 Xbox 360 Slim

Contents

I removed the thumb drive and rebooted to green lights. hope this helps.You most likely need to reflow. I gave up on it technically because I bought an elite, but I still am confident I could fix it. Even though there are a couple different brands used for the mosfets, I have only seen this one controller chip on the bottom of older boards. navigate to this website

The xbox 360 uses special transistors called "metal–oxide–semiconductor field-effect transistors", or MOSFETs to regulate the volatege. Anmelden 347 2 Dieses Video gefällt dir nicht? To provide a better service for everyone, purchasing Premium not only supports the site, but provides for further site progression and grants access to lots of exclusive privileges. Back to top #6 ColKurtz ColKurtz X-S Expert Members 676 posts Posted 11 December 2009 - 05:53 AM Sorry to dig this up, but I ran across this thread when I https://xbox-experts.com/errorcode/E02/0002/

Xbox 360 Error 0002 Fix

Back to top #13 hobo1599 hobo1599 X-S Enthusiast Members 3 posts Posted 01 March 2010 - 09:00 PM tried it and it still gives 3 lights and error code 0002. A dental hook tool, or hemostats should work fine. Newer Than: Search this thread only Search this forum only Display results as threads Useful Searches Recent Posts More... Tried reflowing JUST the CPU with a heat gun and poured some no clean flux underneath it.

When the braid starts to get saturated with solder, move to a fresh piece of braid and keep wicking until all the solder is removed. Solutions:Clean your heatsinks and add a very very small amount of Arctic Cooling Paste between the GPU and the heatink and the GPU and the heatsink....THIS IS VERY IMPORTANT. I could even see the GPU sink "bowed" over the processor. Top 2 reasons you will get a E02 or 0002 error after Xclamp mod.Symptoms: You perform the xclamp mod and when attempting to overheat your GPU you turn on the Xbox,

Therefore, by measuring the voltage drop across the coil, the motherboard knows how much current is being used, and it will shut itself off if too much current is being drawn If you try to remove this capacitor, the XBOX release for you a nice code "0002". ;) seve91 on 2011-03-01 23:49:55 : solved by reballing GPU! Back to top #2 boxecutioner boxecutioner X-S Young Member Members 54 posts Location:Indiana Xbox Version:v1.0 360 version:unknown Posted 28 March 2009 - 08:27 AM arctic silver is a joke, use regular

Wähle deine Sprache aus.

i have fixed a lot of 360s. A controller chip controls the MOSFETs to regulate an exact voltage. Also make sure there are no metal burrs from drilling the new screwholes in the case. Its still fixable with these errors.

  1. i have an ohm meter but i dont know a lot about electronics and where to put the connectors to test it)when i was pulling off the xclamps, i did scrape
  2. So I figured there is a short somewhere.
  3. Fri Apr 03, 2009 1:55 am luchoedu Newbie Joined: Tue Apr 14, 2009 9:05 pmPosts: 1 Re: Xbox 360 Possible 0001 and 0002 error fix...
  4. You MUST have neoprene or nylon washers between the motherboard and the other metal washers used to space between the chassis.
  5. Wird geladen...
  6. NewsTutorialsShopForums Home >> Xbox Repair Guide >> Editable Xbox 360 Error code Database / List >> Add a new Error code >> Edit an existing Error code Login
  7. Hinzufügen Möchtest du dieses Video später noch einmal ansehen?

Xbox 360 Error Codes

Racoon on 2012-05-17 11:10:21 : Just had this error, it was the row of caps on the RHS of the CPU, resolder them all good. :) Racoon on 2012-05-17 10:32:13 Please allow up to 5 seconds… DDoS protection by CloudFlare Ray ID: 2ef6c6ec63140893 Home About Code Contact Uncategorized bios xbox 360 windows script ipod linux palm gtalk web tv diy adsense Xbox 360 Error 0002 Fix This is done via DC-DC switching converters. i even tried a reflow with my heat gun.

does anyone have any suggestions?thanks. http://strongboxlinux.com/xbox-360/e68-xbox-360-slim-error.php unless loosening the screws for your x-clamp does the trick you will need the heat gun. Do these steps and theres a good chance those e02 (0002) errors will go away!TIP: It is much safer to perform the overheat if you only overheat the GPU. Holding the negative probe (-) on the center pin (drain), move the positive probe (+) to the right pin (source).

Nice. If your console is still covered by the 3 year warranty use it because Microsoft will fix it for free! Nice. http://strongboxlinux.com/xbox-360/error-0002-xbox-360-jasper.php Suggestions?

Somehow it was crushed when removing the xclamps. adolfoambriz on 2010-11-28 02:18:25 : I just did this hybrid X clamp mod to my XBOX and it did worked for a couple of days, but now I have this 102 Let it all cool, then put the 360 back together and test it out. 260C for 10 seconds is the absolute max temp tolerance for the mosfets during soldering.

Melde dich an, um dieses Video zur Playlist "Später ansehen" hinzuzufügen.

Then used a neoprene washer and a metal washer between the Motherboard and the heatsinks. I have seen three cases of this happening so far. hope this helps.QUOTE(SwisyNinja @ Feb 19 2010, 09:50 PM) im gettn 0002 wo any heatsinks but also w heatsinks. Username Password I've forgotten my password Remember me This is not recommended for shared computers Sign in anonymously Don't add me to the active users list Privacy Policy ERROR The

Therefore, by measuring the voltage drop across the coil, the motherboard knows how much current is being used, and it will shut itself off if too much current is being drawn Back to top #14 hyfall381 hyfall381 X-S Expert Members 602 posts Location:Connecticut Xbox Version:v1.0 360 version:v1 (xenon) Posted 14 August 2010 - 09:53 PM having the same problem. Here is some info on 0001 and 0002 error 0001 0002 Spoiler You can not test a mosfet chip while it is in circuit, so it must be desoldered first if get redirected here Generated Mon, 10 Oct 2016 04:15:07 GMT by s_ac15 (squid/3.5.20)

knightmire on 2014-04-28 04:13:31 : I can confirm that the "C8U1" component caused this issue for me. i have an ohm meter but i dont know a lot about electronics and where to put the connectors to test it)when i was pulling off the xclamps, i did scrape Wird geladen... in Falcon boards.... [Click here to view the link] The controller chip for the falcon board is.... [Click here to view the link] Like x 4 Comrade, Jan 2, 2011

If you are having a hard time removing the mosfet, try preheating the area a bit first with a heatgun, or soldering torch from a distance. Lythius on 2011-06-20 19:15:26 : I have solved replace the C8U1 because it was open... Not sure what paste it was and if when heated can bridge these connections. You can also check your 360 with another working power brick. 1) If it doesn’t work – Your 360 is faulty. 2) If its does – Your Power brick is faulty

Tested mosfets as per a guide I found and related ones seemed normal. I've had this Xbox as my backup for when I have nothing to work on and I think it's about time to end this little distraction. I looked up on what the 2 red rings mean "overheating" so the Microsoft website said. Even a small burr will throw your spacing off.

The xbox 360 uses special transistors called "metal–oxide–semiconductor field-effect transistors", or MOSFETs to regulate the volatege.MOSFET(Metal–Oxide–Semiconductor Field-Effect Transistor)A MOSFET is a transistor used for amplifying or switching electronic signals.They can be I used 3 washers and a neoprene between the chassis. working fine now! max1zzz on 2013-04-21 00:31:28 : Had this on a xenon after a CPU swap (Downgrading dash to a jtagable version :) ) reflowed the CPU again and it worked fine Also

how can i check? (please be specific... Kategorie Menschen & Blogs Lizenz Standard-YouTube-Lizenz Mehr anzeigen Weniger anzeigen Wird geladen... Holding the negative probe (-) on the center pin (drain) touch the positive probe (+) to the left pin (gate). WiedergabelisteWarteschlangeWiedergabelisteWarteschlange Alle entfernenBeenden Wird geladen...

I go to overheat the system in the RROD fix and it flashes 2 red rings..still..... karol19761976 on 2014-02-01 18:46:44 : 0002 - Reflow CPU - płyta falcon 2008 - konsola po tym zabiegu działa bez problemu chrismwarren on 2013-05-14 00:43:00 : Got this (0002) and Got rid of the xclamps, and then baked in a conventional oven at 250F for 15 min. Solutions:Clean your heatsinks and add a very very small amount of Arctic Cooling Paste between the GPU and the heatink and the GPU and the heatsink....THIS IS VERY IMPORTANT.